HP Concrete Cold Patch

FEATURES & BENEFITS
• Unique gray color, which blends with both concrete or
oxidized asphalt
• Ready to use bags prevent waste and save money
• No mixing, mechanical compaction or tacking
• No messy clean up
• Open to traffic immediately
• DOT approved
• For use in all seasons

AVAILABLE
• Easy to use 50 lb bag

HP Concrete Cold Patch™ offers a solution for both
sides of the pavement universe. Featuring a unique gray
color and special design, HP Concrete performs extremely
well in repairs to either asphalt or concrete surfaces. With
10 years of proven success, the results speak for
themselves.
Our innovative combination of construction-grade aggregate
and proprietary polymer-modified resin base delivers multiple
benefits. The gray color matches both concrete and oxidized
asphalt, and its formulation results in a strong but flexible
repair that delivers semi-permanent to permanent results
based on pavement condition.
With HP Concrete Cold Patch, you get a versatile
pavement repair that looks great and performs even better.
Repair wide cracks, potholes &
other voids quickly & completely in
concrete & asphalt
HP Concrete Cold Patch
One Repair Solution for Proven Results on Multiple Surfaces

HP Concrete Cold Patch is a unique, gray-colored, cold-applied patching material used to repair potholes,
spalls, cracks, and other confined voids and distresses over 1″ wide (2.5 cm) and greater than 1/2″ (1 cm) deep in Portland
cement concrete and oxidized asphalt. It can be used on roads, highways, streets, airport pavements, parking lots, bridge
and parking decks, sidewalks, walkways, and floors. No mixing, heating, or special installation equipment is required.

INSTALLATION
• Clean, sweep, and blow the repair area free of all loose debris before applying.
• The repair area surfaces can be damp but should not have standing water or ice present
during installation.
• Remove HP Concrete Cold Patch from the bag and place it into the prepared repair area.
• For best performance, HP Concrete Cold Patch should be applied with at least 1/2″ (1 cm) in thickness. For repairs 1/2″
(1 cm) to 2″ (5 cm) thick, apply product in a single layer and compact. Repairs deeper than 2″ (5 cm) should be filled in
layers, from 1″ (2.5 cm) to 2″ (5 cm) thick, with compaction of each layer. The final layer should be placed approximately
1/4″ (.6 cm) to 1/2″ (1 cm) above the surface, and then be compacted to surface level with a hand or mechanical tamper
or multiple passes from a vehicle tire.
• Following compaction, clean up any excess HP Concrete Cold Patch and open pavement to traffic. Tip: If needed
in warm climates, initial surface tack can be reduced with a light sprinkle application of Portland cement, calcium
carbonate powder, or fine sand over the compacted surface.
HP Concrete Cold Patch should be installed when pavement temperatures are between 30°F (-1°C) and 100°F (38°C). If
applying when pavement temperatures are below 30°F (-1°C), the repair area can be warmed to at least 30°F (-1°C) using a
Hot Air Lance™ or a torch. HP Concrete Cold Patch can be stored in a warmer area, not exceeding 90°F (32°C), prior to
use, to improve workability.

STORAGE
Pallets and bags of HP Concrete Cold Patch should be kept intact and stored under cover. Shelf life of properly stored product in
unopened pallets and bags is up to one year. To maintain workability, leftover HP Concrete Cold Patch from an opened bag should be
placed in an airtight container such as a pail or bucket with a tight-fitting lid.
USAGE GUIDE
50 IB (22.7 KG)
HP COLD PATCH BAG
Repair Area Size Depth Quantity per Repair
6″ x 6″ (15 cm x 15 cm) 1″ (2.5 cm)
2″ (5 cm)
0.05 bag
0.1 bag
12″ x 12″ (30 cm x 30 cm) 1″ (2.5 cm)
2″ (5 cm)
0.2 bag
0.4 bag
24″ x 24″ (61 cm x 61 cm) 1″ (2.5 cm)
2″ (5 cm)
0.8 bag
1.6 bag